Installation Guide
Tools Needed:
- Hex wrenches (included)
- Phillips screwdriver
- Spanner wrench
- Leveling card or paper
- Pliers
Step-by-Step Assembly
- Unbox and Inventory: Carefully unbox all components and verify all parts against the included checklist.
- Frame Assembly: Assemble the aluminum extrusion frame according to the provided diagram, ensuring all connections are tight.
- Install Motion System: Mount the X, Y, and Z-axis stepper motors, belts, and rails, ensuring smooth movement.
- Mount Print Bed: Install the heated glass bed and secure it to the Y-axis carriage.
- Install Extruder Assembly: Mount the hotend assembly to the X-axis, ensuring proper alignment.
- Electrical Connections: Connect all motors, endstops, heated bed, and hotend to the main control board.
- Level the Bed: Perform manual bed leveling using the paper method, then run auto-leveling if equipped.
- Test Run: Perform a test print to verify proper assembly and calibration.
Specifications
| Model Series | Ender 5 Plus |
| Type | FDM 3D Printer |
| Build Volume | 350 x 350 x 400 mm |
| Layer Resolution | 0.1 - 0.4 mm |
| Print Speed | 60-80 mm/s (recommended) |
| Noise Level | ≤ 50 dB |
| Control Type | Touch Screen with Marlin Firmware |
| Hotend Temperature | Up to 260°C |
| Bed Temperature | Up to 110°C |
| Power Requirements | 110V/220V, 50-60Hz, 350W |
| Dimensions (HxWxD) | 740 x 680 x 780 mm |
| Weight | 21.5 kg |
| Filament Diameter | 1.75 mm |
Warranty Information
- Full Warranty: 1 year parts and labor
- Mainboard Warranty: 2 years on main control board
- Technical Support: Lifetime online support
For warranty service, contact Creality Customer Service at [email protected] or visit creality.com
Key Features
Large Build Volume
350x350x400mm build volume allows printing of large prototypes, cosplay parts, and functional components in a single print.
Dual Z-Axis Screws
Dual Z-axis lead screws with independent motors ensure exceptional stability and precision for tall prints.
Touch Screen Interface
4.3-inch color touch screen provides intuitive control, file management, and real-time monitoring of print progress.
Resume Print Function
Automatically saves print progress and can resume printing after power failure, preventing wasted time and materials.
Carborundum Glass Bed
Special textured glass build surface provides excellent adhesion while printing and easy removal once cooled.
Upgradable Design
Open-source design allows for extensive modifications and upgrades including direct drive, auto-leveling, and silent boards.
Printing Technology Explained
FDM Technology
Fused Deposition Modeling melts and extrudes thermoplastic filament layer by layer to create 3D objects.
Precision Motion
V-slot aluminum extrusion and precision linear rails ensure smooth, accurate movement in all axes.
Thermal Management
PID-controlled heating system maintains stable temperatures for consistent print quality.
Filament Detection
Optional filament runout sensor pauses printing when filament is exhausted, allowing for spool changes.
Silent Operation
TMC2208 stepper drivers (upgraded models) provide near-silent operation during printing.
Network Connectivity
Compatible with Raspberry Pi and OctoPrint for remote monitoring and control via network.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Printer won't start | Power issue, faulty power supply | Check power cable, verify power switch is on, check fuse |
| Poor bed adhesion | Unlevel bed, incorrect nozzle height, dirty bed | Re-level bed, adjust Z-offset, clean bed with isopropyl alcohol |
| Extruder clicking | Nozzle clog, extruder tension too tight | Clean nozzle, adjust extruder spring tension, increase temperature |
| Layer shifting | Loose belts, mechanical obstruction | Tighten belts, check for obstructions, reduce print speed |
| Stringing/oozing | Temperature too high, retraction settings | Lower temperature, increase retraction distance/speed |
| Warped prints | Bed temperature too low, cooling too fast | Increase bed temperature, use enclosure, add brim/raft |
Common Error Messages
- THERMAL RUNAWAY: Heating failure - Check thermistor and heater connections
- HOMING FAILED: Endstop issue - Check endstop switches and wiring
- NOZZLE TOO COLD: Temperature error - Check heater cartridge and thermistor
- FILE READ ERROR: SD card issue - Format SD card or use different card
- MOVEMENT ERROR: Mechanical obstruction - Check for binding or obstructions
- OVERHEAT ERROR: Cooling failure - Check fans and ventilation
Manual Downloads
Current Model Manuals
Ender 5 Plus
Standard Edition
Ender 5 Plus Pro
Upgraded Edition
Ender 5 Plus S1
Direct Drive Edition
Ender 5 Plus BLTouch
Auto-Leveling Edition
Related Models
Ender 5
Standard 220x220x300mm
Ender 5 Pro
Upgraded Components
Ender 3 V2
220x220x250mm
CR-10 V3
300x300x400mm