Installation Guide
Tools Needed:
- Hex key set (included)
- Phillips screwdriver
- Spanner wrench
- Leveling card
- Pliers
Step-by-Step Installation
- Unbox and Inspect: Carefully remove all components from packaging and verify all parts are included according to the parts list.
- Frame Assembly: Assemble the aluminum frame using the provided screws and hex keys, ensuring all connections are tight.
- Install Motion System: Mount the X, Y, and Z axis rails and install the stepper motors with proper belt tension.
- Install Print Head: Mount the extruder assembly and hotend, connecting all cables to the appropriate ports on the mainboard.
- Install Build Plate: Attach the heated bed, ensuring it is properly leveled and secured.
- Electrical Connections: Connect power supply, mainboard, and all electronic components following the wiring diagram.
- Initial Calibration: Perform bed leveling, Z-offset calibration, and test all axis movements.
- Test Print: Load filament and run the included test print to verify proper operation.
Specifications
| Model Series | Creality Print 6 |
| Type | FDM 3D Printer |
| Build Volume | 300 x 300 x 400 mm |
| Layer Resolution | 0.05 - 0.4 mm |
| Print Speed | 20-150 mm/s |
| Nozzle Diameter | 0.4 mm (Standard) |
| Hotend Temperature | Up to 300°C |
| Bed Temperature | Up to 120°C |
| Filament Diameter | 1.75 mm |
| Print Technology | Fused Deposition Modeling |
| Connectivity | USB, SD Card, Wi-Fi, Ethernet |
| Power Requirements | 110-240V, 50-60Hz, 350W |
| Dimensions | 550 x 550 x 650 mm |
| Weight | 18 kg |
Warranty Information
- Full Warranty: 1 year parts and labor
- Mainboard Warranty: 2 years
- Hotend Warranty: 6 months
- Additional Coverage: Optional extended warranty available
For warranty service, contact Creality Customer Service at 1-800-555-3DPRINT or visit creality.com
Key Features
Dual Z-axis System
Independent dual Z-axis motors provide exceptional stability and precision, ensuring consistent layer height and improved print quality throughout the build volume.
Auto Bed Leveling
Advanced 25-point auto bed leveling system with capacitive sensor ensures perfect first layer adhesion across the entire build surface.
Direct Drive Extruder
High-torque direct drive extruder provides superior filament control, enabling printing with flexible materials and reducing stringing.
Silent Mainboard
TMC2209 stepper drivers provide near-silent operation while maintaining precise motor control and reducing vibration artifacts.
Touch Screen Interface
4.3-inch full-color touch screen with intuitive menu system for easy printer control, calibration, and monitoring.
Filament Runout Sensor
Integrated filament detection pauses printing when filament runs out, allowing for seamless filament changes without print failure.
Print Technology Explained
High Speed Mode
Optimized for rapid prototyping with accelerated print speeds up to 150mm/s
High Precision Mode
Ultra-fine 0.05mm layer height for detailed models and miniature prints
Flexible Material Mode
Specialized settings for TPU and other flexible filaments with reduced retraction
ABS/ASA Mode
Enclosed chamber heating and optimized temperatures for engineering materials
PETG Mode
Balanced settings for strong, durable prints with minimal stringing
PLA Mode
Standard settings for reliable printing with the most common filament type
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Printer won't power on | Power switch off, loose cable, faulty power supply | Check power switch, ensure all cables are secure, test outlet |
| Poor bed adhesion | Unlevel bed, incorrect Z-offset, dirty build surface | Re-level bed, adjust Z-offset, clean with isopropyl alcohol |
| Extruder skipping | Clogged nozzle, incorrect temperature, extruder tension | Clean nozzle, adjust temperature, calibrate extruder steps |
| Layer shifting | Loose belts, mechanical obstruction, overheating drivers | Tighten belts, check for obstructions, ensure proper cooling |
| Stringing/oozing | High temperature, insufficient retraction, moist filament | Lower temperature, increase retraction, dry filament |
| Under-extrusion | Partial clog, extruder slipping, low temperature | Perform cold pull, check extruder gear, increase temperature |
Error Codes
- E1: Heating failed - Check thermistor and heater cartridge
- E2: Bed heating failed - Check bed thermistor and heater
- E3: Thermal runaway - Check cooling and thermal sensors
- E4: Filament runout - Load new filament and resume
- E5: Over-temperature - Allow to cool and check cooling system
- E6: Under-temperature - Check heating elements and power
Manual Downloads
Current Model Manuals
CP6-STD
Creality Print 6 Standard
CP6-PRO
Creality Print 6 Pro
CP6-PLUS
Creality Print 6 Plus
CP6-ENCL
Creality Print 6 Enclosed
Popular Previous Models
Ender-3 V3
Previous Generation
CR-10 V3
Large Format Printer
Ender-5 Plus
CoreXY Design
CR-6 SE
Community Edition