Installation Guide
Tools Needed:
- Hex key set (included)
- Screwdriver (Phillips)
- Leveling card (included)
- Pliers
- Cleaning cloth
Step-by-Step Installation
- Unpack and Inspect: Carefully remove all packaging materials and check all components against the packing list.
- Assemble Frame: Follow the assembly diagram to connect the main frame components using provided screws and tools.
- Install Print Head: Mount the extruder assembly onto the X-axis carriage, ensuring all cables are properly routed.
- Connect Electronics: Connect all cables to the control board according to the labeled ports and secure with cable ties.
- Level Build Plate: Use the automatic bed leveling feature and manual adjustment to ensure proper first layer adhesion.
- Load Filament: Insert filament through the feeder and into the extruder, following the on-screen instructions.
- Test Print: Run the included test print to verify proper assembly and calibration.
Specifications
| Model Series | Guider 2 |
| Type | FDM 3D Printer |
| Build Volume | 280 × 250 × 300 mm |
| Layer Resolution | 0.05 - 0.3 mm |
| Nozzle Diameter | 0.4 mm (standard) |
| Print Speed | 10 - 100 mm/s |
| Filament Diameter | 1.75 mm |
| Hotend Temperature | Max 300°C |
| Bed Temperature | Max 120°C |
| Power Requirements | 110-240V, 50-60Hz, 350W |
| Dimensions (HxWxD) | 580 × 500 × 620 mm |
| Weight | 28 kg |
| Connectivity | USB, Ethernet, Wi-Fi, SD Card |
Warranty Information
- Full Warranty: 1 year parts and labor
- Hotend Warranty: 6 months on print head assembly
- Additional Coverage: Optional extended warranty available
For warranty service, contact Flashforge Customer Service at 1-800-313-9023 or visit Flashforge.com
Key Features
Dual Extrusion System
Independent dual extruders allow printing with two colors or materials simultaneously, with automatic nozzle lifting to prevent oozing and collisions.
Automatic Bed Leveling
16-point automatic bed leveling system ensures perfect first layer adhesion across the entire build plate, reducing failed prints and manual calibration.
Enclosed Chamber
Fully enclosed printing chamber maintains consistent temperature for printing advanced materials like ABS, nylon, and polycarbonate with minimal warping.
HEPA Air Filter
Built-in HEPA filtration system captures ultrafine particles and odors, making printing safer for indoor environments and reducing VOCs.
Touch Screen Interface
5-inch full-color touch screen provides intuitive control over all printer functions, file management, and real-time monitoring.
Filament Detection
Smart filament sensor automatically pauses printing when filament runs out or breaks, allowing for easy reloading without losing progress.
Printing Technology Explained
FDM Printing
Fused Deposition Modeling technology for precise layer-by-layer construction
Dual Extrusion
Simultaneous printing with two materials for complex multi-color models
High Temp Printing
Capable of printing engineering-grade materials up to 300°C
Network Printing
Wireless printing capability for remote monitoring and control
Resume Printing
Automatic resume function after power interruption
Camera Monitoring
Optional camera for remote print monitoring via network
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Printer won't start | Power issue, main switch off, faulty cable | Check power supply, ensure main switch is on, replace cable if damaged |
| Poor first layer adhesion | Bed not level, wrong bed temperature, dirty build surface | Re-level bed, adjust temperature settings, clean with isopropyl alcohol |
| Filament not extruding | Nozzle clogged, extruder gear slipping, filament jam | Clean nozzle, check extruder tension, clear filament path |
| Layer shifting | Belt tension loose, mechanical obstruction, overheating drivers | Tighten belts, check for obstructions, ensure proper cooling |
| Stringing/oozing | Retraction settings incorrect, temperature too high | Adjust retraction settings, lower printing temperature |
| Warped prints | Bed temperature too low, cooling too fast, draft in room | Increase bed temperature, reduce cooling fan speed, use enclosure |
Error Codes
- E01: Heater error - Check hotend thermistor and heater cartridge
- E02: Bed heater error - Check bed thermistor and heater
- E03: Thermal runaway - Check cooling system and temperature sensors
- E04: Motor stall - Check for mechanical obstruction or binding
- E05: Filament error - Check filament sensor and loading
- E06: Communication error - Check USB/Ethernet connection
Manual Downloads
Current Model Manuals
Guider 2
Standard Edition
Guider 2S
Upgraded Edition
Guider 2 Plus
Enhanced Features
Guider 2 Pro
Professional Edition
Popular Previous Models
Guider I
Original Guider Series
Creator Pro
Dual Extrusion Printer
Adventurer 3
Compact 3D Printer
Dreamer NX
Dual Nozzle Printer